USBLAN Troubleshooting and Diagnostics Guide
Use this page as an engineering runbook for isolating host and device USB networking issues on Windows 11 (AMD64 and ARM64) and Windows 10 (AMD64) systems.
Baseline diagnostic capture
- Host OS version and architecture (AMD64 or ARM64)
- Device firmware build and USB descriptor dump
- Selected protocol mode (CDC-NCM, CDC-ECM, CDC-EEM, or RNDIS)
- Driver package version currently installed in Windows Driver Store
Windows Device Manager error codes
When Windows encounters an issue initializing a USB network peripheral, Device Manager displays a status error code on the device node:
Code 28: Drivers for this device are not installed
Cause: Windows Plug-and-Play (PnP) cannot find an INF file matching the hardware identifier presented by the USB device.
Remedy: Verify the 16-bit Vendor ID (VID) and Product ID (PID) in your device descriptors against the INF file. For composite devices, verify that the sub-interface identifier (&MI_xx) matches the network interface index defined in your firmware or ConfigFS gadget definition. If testing an updated driver package, consult the Driver Store Cleanup Guide below to ensure stale OEM packages do not block binding.
Code 10: This device cannot start
Cause: The USBLAN driver was matched and loaded by Windows, but failed during protocol handshake, endpoint allocation, or initialization with the device firmware.
Remedy: Check USB BULK endpoint configurations in firmware (verify endpoint addresses, max packet size, and transfer directions). For CDC-NCM or CDC-ECM gadgets, ensure the device responds promptly to control requests on Endpoint 0 (such as SET_ETHERNET_PACKET_FILTER or GET_NTB_PARAMETERS) without timing out.
Code 43: Windows has stopped this device because it has reported problems
Cause: Low-level USB bus communication failure, port reset timeout, or device controller firmware crash during bus enumeration.
Remedy: Check physical USB cable integrity, signal quality, and power delivery. Review USB peripheral controller (UDC) register dumps on the device. When using Linux USB gadgets, verify ConfigFS binding using tools described in the USB Gadget Configuration Guide.
Driver store cleanup and clean uninstall (pnputil)
When testing prototype firmware, updating driver packages, or resolving Device Manager Code 28 conflicts, use this procedure to remove stale USBLAN packages from the Windows Driver Store:
- Disconnect the target device when possible to prevent Windows from immediately re-enumerating and rebinding.
- Remove the device instance: In Device Manager, right-click the device under Network Adapters, select Uninstall device, and check Attempt to remove the driver for this device.
- Enumerate and delete OEM packages with pnputil: Open an elevated Command Prompt or PowerShell and inspect the Driver Store:
pnputil /enum-drivers
pnputil /delete-driver oemXX.inf /uninstall /force
Verification and recovery:
- Confirm that no stale network adapter entries remain in Device Manager (enable View > Show hidden devices if necessary).
- Reconnect the device and verify that Windows Plug-and-Play loads the intended package version.
Network layer and connectivity symptoms
Device enumerates but no network interface appears
Likely causes: Protocol or interface mismatch, missing package binding, or composite interface selection mismatch.
Verify: Check Device Manager instance details, hardware IDs (including &MI_xx), and active driver service binding.
Resolve: Correct INF device matching, stage the intended package via pnputil, reconnect and confirm NDIS adapter creation.
Interface appears but no IP connectivity
Likely causes: IP address assignment failure, DHCP lease timeout, subnetwork conflict, or gadget-side link-state handling.
Verify: Run ipconfig /all to inspect host IP configuration, verify whether an APIPA address (169.254.x.x) was assigned, and confirm device-side DHCP server responsiveness.
Resolve: Align host and device addressing models and verify point-to-point subnetwork configuration as detailed in the Address Management and Device Discovery Guide.
Throughput lower than expected
Likely causes: Suboptimal transfer aggregation, protocol selection mismatch, power policy throttling, or device firmware buffer limits.
Verify: Compare throughput across protocols using our USB Networking Protocols Guide. For CDC-NCM, confirm that multi-frame Network Transfer Block (NTB) aggregation is active.
Resolve: Tune protocol and transfer parameters in firmware, and verify sustained throughput after sleep and resume cycles.
Intermittent disconnects after sleep and resume
Likely causes: Host power policy interaction, firmware resume timing, or stale adapter state after system wake.
Verify: Reproduce with controlled Modern Standby (S0ix) or suspend cycles, and collect Windows system event logs.
Resolve: Adjust selective suspend settings, validate firmware resume timing, and confirm recovery across repeated wake cycles.
Diagnostic and automated test tools
Kernel-mode trace logging with DebugView
For driver diagnostics, protocol negotiation analysis, and bring-up troubleshooting, Belcarra USBLAN drivers emit diagnostic output viewable via Microsoft Sysinternals DebugView (Dbgview.exe):
- Production driver output: Drivers in both evaluation kits and regular licensed kits are labelled Production. They generate a concise set of initialization messages displaying the driver version, build number, and active INF option settings.
- Verbose debugging with checked/debug kits: If your engineering team requires verbose packet-level tracing, endpoint pipe state transitions, CDC-NCM NTB framing parameters, or Endpoint 0 control request monitoring, contact Belcarra to request a dedicated checked/debug (chk) driver kit.
- Capturing kernel output: Launch DebugView as Administrator and enable Capture Kernel from the Capture menu (or press Ctrl+K). On Windows 11 and Windows 10 (AMD64), ensure that kernel debug print capture is enabled.
- Filtering and saving: Use DebugView's Include filter (e.g.
USBLAN*) to isolate Belcarra driver messages from general Windows kernel debug traffic, and use File > Save As to save logs for technical support reviews.
Automated cable replug cycling (usbtestnet)
For reproducible diagnostics and stress testing during prototype bring-up, Belcarra maintains the open-source usbtestnet Windows test harness:
- Simulated cable replugging: Uses
devconto programmatically cycle USB device enable and disable states by Vendor ID (VID) and Product ID (PID) without physical intervention. - Link bring-up validation: Automatically measures adapter enumeration time, confirms network interface availability, and verifies DHCP or static IP acquisition.
- End-to-end traffic verification: Executes continuous ping loops and HTTP GET transactions across cycles, logging byte and packet statistics to isolate intermittent dropouts or timing regressions.
- Available on GitHub: Source script (
usbtestnet.py) and standalone executable available at Belcarra/usbtestnet.
Recommended evidence bundle for engineering support
When reporting an issue or contacting Belcarra engineering support via the Contact Form, include the following details:
- Host OS build, version, and architecture (AMD64 or ARM64)
- Protocol mode and complete USB descriptor snapshot for the device
- Device Manager status and error code (e.g., Code 10, 28, or 43)
- Step-by-step reproduction sequence
- Expected result versus observed result
- DebugView kernel trace log capture and
usbtestnetsession logs